High-Performance 19 dBi airMAX® ac CPEModel: NBE-5AC-19
Connecting to the PoE Adapter1. Remove the port cover by pressing down the center of the cover and sliding the cover out.2. Connect an Ethernet cabl
4. Connect the other end of the Ethernet cable from the NanoBeam to the Ethernet port labeled POE on the Gigabit PoEAdapter.5. Connect an Ethernet
Accessing airOSVerify connectivity in the airOS Configuration Interface. 1. Make sure that your host machine is connected via Ethernet to the NanoBea
Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer's responsibility to make sure th
SpecificationsNBE-5AC-19Dimensions (Mount Included) 189 x 189 x 125 mm (7.44 x 7.44 x 4.92")Weight (Mount Included) 530 g (1.17 lb)Operating Freq
Safety Notices1. Read, follow, and keep these instructions.2. Heed all warnings.3. Only use attachments/accessories specified by the manufacturer.W
Limited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from de
DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE
NoteSome countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You
This radio transmitter (FCC: SWX-NBEAC) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and
IntroductionThank you for purchasing the Ubiquiti Networks® NanoBeam®. This Quick Start Guide is designed to guide you through the installation, and s
Les utilisateurs devraient également noter que radars haute puissants sont alloués comme principaux utilisateurs (c’est-à-dire les utilisateurs de pri
RoHS/WEEE Compliance StatementEnglishEuropean Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging
EspañolLa Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junt
Declaration of ConformityČesky [Czech]UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal
©2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, EdgeRouter
Installation RequirementsThe NanoBeam can be mounted on a pole or to a wall. A Metal Strap (included) is used for pole-mounting. For wall-mounting, a
Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the NanoBeam is already poweredon. Alterna
Hardware InstallationThe NanoBeam can be mounted on a pole or to a wall. Perform the steps for the appropriate installation:Pole-Mount1. Insert the B
*640-00127-06*640-00127-063. Wrap the Metal Strap around the pole. Use a 7 mm socket wrench to turn the screw clockwise and securely fasten the clamp
Wall-MountThe NanoBeam must be mounted directly to a wood stud or other structurally stable surface to avoid damage to the mounting hole when you adju
4. If you are using the optional NanoBeam Wall Mount Kit, then skip to step b.a. To attach the Ball Joint Mount to the wall, insert a fastener (not
5. Attach the NanoBeam to the Ball Joint Mount and turn the Lock Ring to secure it. Keep the Lock Ring loose enough to allow the NanoBeam to pivot fo
Commentaires sur ces manuels